How to: speed up your wireless internet connection on Windows XP

1. Move the wireless router to a better location

The first thing you want to do is to make sure your wireless router is in the best location possible. If you have a laptop that you move around all the time or if you have several computers, the router should be in the centre of your home and office. Don’t hide it into cupboards, or under chairs and tables.

But if you only have one stationary computer, use a cable connection to the router or move the router as close to the computer as possible.

You can check the signal strength from the Wireless connection menu, accessible from Start -> Connect To -> Wireless Connection. You can also access it by clicking the wireless icon at the bottom right corner of the screen if you are connected.
2. Upgrade the wireless router firmware

Sometimes the problem is with the router firmware. Make sure you update your router firmware as often as possible to avoid incompatibility with newer systems. You can update your router firmware from the wireless router control panel. Type your router’s IP address into the browser to access the CP.

The default IP of routers is normally 192.168.1.1 for Linksys, 192.168.0.1 for D-Link and Netgear, some US Robotics routers use 192.168.123.254 and some SMC routers have 192.168.2.1. The router’s default IP address is always in the documentation of the router.
3. Change the wireless broadcast channel

If there are several wireless networks in your area, they can begin to distract each other. Most routers use the wireless channel 6 by default and the channel can slow down if full of signals coming from many routers. You can change the wireless channel from the Wireless Control Panel.

If changing the channel didn’t speed up your wireless connection, change it back to 6. It’s better not to play with them too much because this can distract your firewall.
4. Update your computer’s wireless network drivers

You can search for driver updates from the Windows Update site or your manufacturers website.

If none of the above tips helped, contact your wireless router manufacturer or just go back to a wired internet connection.

How To: Display The Shutdown Menu When Your Computer’s Power Button Is Pressed

By default, your Windows XP will shut down when the Power button is pressed. It’s a good idea to change it so that the shutdown menu is opened instead, especially if you have little kids running around the house.
It’s quite easy to change it:
Step 1:
Go to your Windows XP’s desktop and right-click it. Select “Properties” and the Display Properties window will appear.
Open the “Screen Saver” tab and look for the “Power” button near the bottom of the window. Click it.

Step 2:
In the “Power Options Properties” window that opens, go to …

How To Bypass The Recycle Bin When Deleting Files

If you are absolutely sure you want to delete a file, why send it to the Recycle Bin? Windows lets you bypass it really easily:

To delete a file or a group of files, select them with and when they are highlighted, press Shift+Delete. Press “Yes” in the confirmation box that opens and you’re done!

SHUTDOWN WORKS, BUT IT’S REAL SLOW.

If it appears that Win XP is not shutting down, give it some time. Some users have reported a minute or longer for shutdown to visibly start. Thus far, it appears that this is a consequence of software that is running when shutdown is attempted, and it also may have something to do with particular hardware. If you are experiencing this problem, be sure to close all running programs before attempting shutdown and see if this solves your problem. If so, then you can determine, by trial and error, which program(s) are involved.
One specific solution for this was provided by Microsoft support.

” In Control Panel | Administrative Tools | Services. (You can also get this by launching SERVICES.MSC from a Run box. This utility is also built into the Computer Management console.) Stop the Nvidia Driver Helper service. Many other friends quickly confirmed that this solved this “extremely slow shutdown” problem for them.

How To Enable Hibernation

Under Windows 98, Me, or 2000 there was an option in the shutdown dialog box to enter the computer into hibernation (where all the content of the RAM is copied to the hard disk). The shutdown dialog box of Windows XP doesn't offer any longer the hibernation button. Some users may get confused about how to enable the hibernation mode. If this mode is supported by your motherboard (ACPI) you have to do the following:

1. Click Start and Shut Down,
2. Point the standby button and maintain the shift key pushed,
3. A new hibernation button appears: click it while still holding the shift key: voila your PC will hibernate.

Getting an Older Program to Run on Windows XP

1.Right–click the executable or the program shortcut to the executable, and then click Properties.

2.Select the Run this program in compatibility mode check box.

3.From the list, select an operating system that the program runs in comfortably.

If necessary, also change the display settings and/or resolution, or disable the Windows XP visual themes.
Run the program again when you’re finished changing the settings. Adjust the compatibility settings again if the program is still not running smoothly: a program that’s unhappy on Windows 2000 may flourish on Windows 98.

Reduce Temporary Internet F ile Space

The temporary internet files clutter your hard drive with copies of each page visited. These can build up over time and take up disk space. Even more bothersome is that instead of getting new pages each time IE often takes the page out the temp internet files. This can be a problem if you are viewing a website that is updated all the time. If you are on a slow connection such as a 56K or lower then this can be good but if you are on a fast broadband connection, like me, then you can get away with decreasing the size of your temp internet files to just one meg without any performance decrease.

Launch Internet Explorer.
Select the Tools from the menu bar.
Then select Internet Options... from the drop down menu.
Once the internet options has loaded click on the general tab.
Under the temporary internet files section click the settings button.
A settings window will load. Slide the slider all the way to the left so the size indicated in the text box on the right is one.
Click OK
Click Ok

Convert a FAT Partition to the NTFS File System

To convert a FAT partition to NTFS, perform the following steps.

Click Start, click Programs, and then click Command Prompt.

In Windows XP, click Start, and then click Run.

At the command prompt, type CONVERT [driveletter]: /FS:NTFS.
Convert.exe will attempt to convert the partition to NTFS.

NOTE: Although the chance of corruption or data loss during the conversion from FAT to NTFS is minimal, it is best to perform a full backup of the data on the drive that it is to be converted prior to executing the convert command. It is also recommended to verify the integrity of the backup before proceeding, as well as to run RDISK and update the emergency repair disk (ERD).

Convert.exe will attempt to convert the partition to NTFS.

Remove shortcut arrow from desktop icons

Here's how you can remove those shortcut arrows from your desktop icons in Windows XP.

1. Start regedit.
2. Navigate to HKEY_CLASSES_ROOTlnkfile
3. Delete the IsShortcut registry value.

Boot Defragment

A very important new feature in Microsoft Windows XP is the ability to do a boot defragment. This basically means that all boot files are placed next to each other on the disk drive to allow for faster booting. By default this option is enabled but some upgrade users have reported that it isn't on their setup.

1. Start Regedit.
2. Navigate to HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Dfrg\BootOptimizeFunction
3. Select Enable from the list on the right.
4. Right on it and select Modify.
5. Change the value to Y to enable and N to disable.
6. Reboot your computer.

Hide 'User Accounts' from users

Go to Start/Run, and type:

GPEDIT.MSC

Open the path

User Config > Admin Templates > Control Panel

doubleclick "Hide specified Control Panel applets"

put a dot in 'enabled', then click 'Show"

click Add button,

type "nusrmgt.cpl" into the add box.

Speed up your browsing of Windows 2000 & XP machines

Here's a great tip to speed up your browsing of Windows XP machines. Its actually a fix to a bug installed as default in Windows 2000 that scans shared files for Scheduled Tasks. And it turns out that you can experience a delay as long as 30 seconds when you try to view shared files across a network because Windows 2000 is using the extra time to search the remote computer for any Scheduled Tasks. Note that though the fix is originally intended for only those affected, Windows 2000 users will experience that the actual browsing speed of both the Internet & Windows Explorers improve significantly after applying it since it doesn't search for Scheduled Tasks anymore. Here's how :

Open up the Registry and go to :

HKEY_LOCAL_MACHINE/Software/Microsoft/Windows/Current Version/Explorer/RemoteComputer/NameSpace

Under that branch, select the key :
{D6277990-4C6A-11CF-8D87-00AA0060F5BF}
and delete it.

This is key that instructs Windows to search for Scheduled Tasks. If you like you may want to export the exact branch so that you can restore the key if necessary.

This fix is so effective that it doesn't require a reboot and you can almost immediately determine yourself how much it speeds up your browsing processes.

Disable CD Autorun

1) Click Start, Run and enter GPEDIT.MSC

2) Go to Computer Configuration, Administrative Templates, System.

3) Locate the entry for Turn autoplay off and modify it as you desire.

Make Use Of Your Windows Key

Windows: Display the Start menu
Windows + D: Minimize or restore all windows
Windows + E: Display Windows Explorer
Windows + F: Display Search for files
Windows + Ctrl + F: Display Search for computer
Windows + F1: Display Help and Support Center
Windows + R: Display Run dialog box
Windows + break: Display System Properties dialog box
Windows + shift + M: Undo minimize all windows
Windows + L: Lock the workstation
Windows + U: Open Utility Manager
Windows + Q: Quick switching of users (Powertoys only)
Windows + Q: Hold Windows Key, then tap Q to scroll thru the different users on your PC

To change disk drive letters

To change drive letters (useful if you have two drives and have partitioned the boot drive, but the secondary drive shows up as "D")

Go to Start > Control Panel > Administrative Tools > Computer Management, Disk Management, then right-click the partition whose name you want to change (click in the white area just below the word "Volume") and select "change drive letter and paths."
From here you can add, remove or change drive letters and paths to the partition.

pc lock via mobile

PC LOCK VIA MOBILEbtprox.pngBTPROX application is a bluetooth application for mobiles and it is used to remotely lock your windows computer when your away from your computer and to perform certain required actions from a distance in your computer.BtProx includes a more advanced feature set, allowing you to set a timeout before it locks your PC and run a program when your device is out of range. I had trouble using it with my iPhone, so if you give it a go, let's hear how it works for you in the comments.it is for windows only...REMOTE LOCK FOR COMPUTER,BLUETOOTH HACKING SOFTWARES

Command Prompt on Right-Click

Many computer users, specially the programmers, need to launch a command prompt window every once in a while to execute some dos/shell commands. The problem is, when a command prompt window launched, the default path is normally the system path or the user profile's path. The users will then have to do all the "cd" commands to change the directories to the path he/she wants.This trick shows you how to add an option called "Command Prompt" when you right-click on a folder in Windows. With this option, a Command Prompt Window will launch and its current directory will be the path to the folder you've selected.Use this trick at your own risk.Here's what you'll get: The SolutionYou can either edit your registry OR download the registry file and apply it on your computer.Method I. Manually edit the registry: 1. Start > Run 2. Enter "regedit" and hit Enter 3. Expand to "HKEY_LOCAL_MACHINE\SOFTWARE\Classes\Folder\shell" 4. Right-click on "shell" and select New > Key 5. Make sure a new key is created under "shell". Change the name of this key to "Command Prompt" 6. Right-click on this new key "Command Prompt" and select New > Key 7. Change the name of this key to "command" 8. Here's what we should have: 9. Double-click on the "(Default)" text on the right window to bring up the edit box 10. Enter this text into the Value Data field: cmd.exe "%1" 11. Click OK and close the registry.